Loading document…
Opening in Pages for Mac...
Your browser isn’t fully supported.
For the best Pages for iCloud experience, use a supported browser.
Learn More
Cancel
Continue
PRODUCED BY
PINBALL
QUINTS REEL - INSTALLATION INSTRUCTIONS
TABLE OF CONTENTS
•
IN THE BOX -
PAGE 2
•
TOOLS REQUIRED -
PAGE 2
•
QUINT’S REEL INSTALL -
PAGE 2-5
•
REEL ADJUSTMENTS -
PAGE 6-7
•
ORCA WHEEL INSTALL -
PAGE 8-9
•
IMPORTANT VISUAL CHECKS -
PAGE
•
FUTURE HOT MODS RELEASE -
PAGE 11
•
STERN SPINNER ASSEMBLY APPENDIX -
PAGE 12
•
RETURNS POLICY & WARRANTY -
PAGE 13
IN THE BOX
•
1 x QUINTS FISHING REEL TOPPER
•
1 x 1/2” HEX BUTTON SCREW
•
2 x 5G SELF ADHESIVE WEIGHTS
•
2 x 1mm FIBRE WASHER/SPACERS
—————————
————————
•
1 x SCULPTED ORCA BOAT WHEEL SPINNER TOPPER
(PREM/LE ONLY)
•
1 x 1” HEX BUTTON SCREW
(PREM/LE ONLY)
•
1 x 1mm FIBRE WASHER/SPACER
(PREM/LE ONLY)
•
1 x 2mm FIBRE WASHER/SPACER
(PREM/LE ONLY)
INSTALL GUIDE
•
INSTALL VIDEO (CLICK HERE) COMING SOON
TOOLS REQUIRED:
•
1/8” ALLEN KEY
•
5/64” OR 2” ALLEN KEY
•
FLAT SLOTTED SCREWDRIVER
•
7MM/M4 SOCKET OR NUT DRIVER
PLEASE READ THROUGH THE ENTIRE DOCUMENT FIRST BEFORE STARTING, TO ENSURE YOU
UNDERSTAND THE FULL SCOPE OF THE INSTALLATION.
IMPORTANT NOTE:
PLEASE WORK CAREFULLY TAKING YOUR TIME, I CAN TAKE NO RESPONSIBILITY FOR DAMAGE
CAUSED TO YOUR GAME DUE TO INCORRECT INSTALLATION OR WORK PRACTICES.
THE FOLLOWING INSTALL REQUIRES YOU TO HAVE PREINSTALLED THE PRECISION PINBALL
SPINNER UPGRADE DISCS AND BUSHINGS.
QUINT’S REEL INSTALL
1.
WITH THE PRECISION
PINBALL DISC UPGRADE
INSTALLED, REMOVE THE
SECURING SCREW FROM
THE CENTRE OF THE
PRECISION PINBALL
SPINNING DISC USING A
1/8” ALLEN KEY
RED
ARROW.
2.
IF YOU HAVE REINSTALLED
THE BLACK FACTORY HEX
SCREWS & WEIGHTED
POST, WHILE WAITING FOR
YOUR SPINNER TOPPERS,
THESE WILL NOW NEED
REMOVING.
3.
REMOVE BOTH HEX SCREWS
GREEN
ARROWS
ALONG WITH THE BLACK FACTORY WEIGHTED POST
YELLOW ARROW
USING A 5/64” OR 2” ALLEN KEY.
4.
THIS IS DONE EASIEST BY HOLDING THE SPINNING DISC IN POSITION WITH ONE HAND AND
REMOVING THE HEX SCREWS FIRST
GREEN
ARROWS
, FOLLOWED BY THE WEIGHTED POST
YELLOW ARROW
AND FINALLY THE CENTRE SECURING SCREW
RED ARROW
.
5.
NOW BEFORE WE BEGIN THE INSTALL OF THE REEL TOPPER, WITH ALL THE FACTORY HARDWARE
REMOVED, TAKE YOUR PRECISION PINBALL DISC OUT OF THE GAME AND FLIP IT UPSIDE DOWN.
6.
TAKE THE TWO ZINC PLATED 5.GRAM WEIGHTS AND APPLY THEM TO THE UNDERSIDE OF THE
PRECISION PINBALL DISC AS SHOWN BELOW.
7.
YOU WANT TO PRESS THEM INTO THE GROVE OF THE RAISED UNDERSIDE AREA, TO GET A CLEAN
AND STREAMLINE INSTALL THAT IS INVISIBLE ONCE THE DISC AND REEL TOPPER ARE INSTALLED.
8.
WITH THE WEIGHTS INSTALLED, PLACE THE PRECISION PINBALL DISC BACK ON TOP OF THE
PRECISION PINBALL BUSHING/SHAFT.
9.
NOW TAKE QUINT’S REEL
TOPPER AND PLACE IT ON
THE PRECISION PINBALL
DISC.
10.
LOCATE THE SECTION ON
THE UNDERSIDE OF THE
PRECISION PINBALL DISC,
THAT WE JUST PLACED
THE WEIGHTS EITHER SIDE
OF IN STEPS #6 & #7 AND
POSITION IT BETWEEN
THE TWO
EYE HOOKS
YELLOW DOTTED LINES
AS
SHOWN IN THE IMAGE TO
THE RIGHT.
11.
WE NOW NEED THE STERN FACTORY WASHER
RED
ARROW
, THAT YOU WOULD HAVE REMOVED FROM
THE FACTORY SPINNER MECH/ASSEMBLY AS SHOWN
IN THE ASSEMBLY IMAGE ON THE RIGHT.
12.
IF YOU ARE UNSURE OF THE WASHERS BEING
REFERRED TO HERE, JUMP DOWN TO PAGE 12
“
APPENDIX ONE: STERN FACTORY WASHERS
” AT THE
END OF THIS INSTALL DOCUMENT. BOTH THE MAIN
PLAYFIELD SPINNER AND UPPER PLAYFIELD SPINNER
(PREM/LE) ASSEMBLY DRAWINGS ARE SHOWN IN
FULL.
READ STEPS 13-16 BEFORE PROCEEDING TO ENSURE
YOU HAVE A CLEAR UNDERSTANDING OF THE VARIOUS
OPTIONS
AVAILABLE
FOR SECURING THE REEL TOPPER
TO THE PRECISION PINBALL SPINNER/DISC.
13.
PLACE THE STERN FACTORY WASHER INSIDE THE
CENTRE RECESS OF THE REEL
YELLOW ARROW
AS
SHOWN IN THE IMAGE JUST BELOW TO THE RIGHT
AND USE THE PROVIDED 1/2” HEX SCREW TO SECURE
THE TOPPER TO THE PRECISION DISC.
14.
PREM/LE OWNERS
ALSO HAVE THE OPTION OF
PLACING A SECOND STERN FACTORY WASHER FROM
THE FACTORY UPPER PLAYFIELD SPINNER ASSEMBLY
INTO THE CENTRE OF THE REEL TOPPER.
15.
DUE TO THE PRODUCTION TOLERANCES
OF THE REEL BASE, THERE MAYBE
EXAMPLES WERE THE 1/2” HEX SCREW
DOES NOT THREAD COMPLETELY INTO
THE PRECISION BUSHING/SHAFT AND
DOES NOT TIGHTEN THE TOPPER TO THE
PRECISION DISC SECURELY, ALLOWING
THEM TO SPIN INDEPENDENTLY.
16.
IF THIS HAPPENS, USE THE HEX SCREW
PROVIDED BY PRECISION PINBALL AS IT
HAS A SHORTER THREAD LENGTH, THIS
CAN BE UTILISED WITH OR WITHOUT A
FACTORY WASHER IN THE CENTRE
RECESS OF THE REEL TOPPER.
17.
ONCE YOU HAVE A SETUP THAT SECURES
THE TOPPER TO THE PRECISION DISC IN
YOUR GAME, WE NOW NEED TO
TIGHTEN THE CENTRAL HEX SCREW FIRMLY.
18.
DO THIS BY HOLD THE TOPPER AND PRECISION DISC TOGETHER, THE EASIEST WAY TO ENSURE
THE TOPPER DOES NOT SPIN/SLIP OUT OF POSITION ON THE DISC IS TO PINCH THEM TOGETHER.
19.
AS YOU TIGHTEN THE CENTRE HEX SCREW ENSURE YOU KEEP THE EYELETS POSITIONED
CORRECTLY, AS DETAILED ON THE PAGE ABOVE IN STEP #6.
THAT COMPLETES THE MAIN INSTALL OF QUINT’S REEL SPINNER TOPPER.
QUINT’S REEL
-
ADJUSTMENT INSTRUCTIONS
I SHIP EACH REEL WITH THE ARM AND HANDLE IN A DEFAULT POSITION, THIS POSITION WORKS
PERFECTLY ON MY OWN INDIVIDUAL GAME AND THE MAJORITY OF OTHERS.
HOWEVER IF UPON TESTING YOUR REEL FOLLOWING THE COMPLETION OF THE INSTALL ABOVE, IT
DOES NOT
SPIN FREELY, PLEASE
FOLLOW THE FOLLOWING STEPS
IN ORDER TO
ADJUST
YOUR REEL
ARM
AND
HANDLE.
THE MAIN ISSUE WILL MOST LIKELY BE CONTACT WITH THE WIREFORM. THE ROOM IN THIS AREA IS
FAIRLY TIGHT AS STERN CLEARLY NEVER PLANNED FOR A 3D REEL. IT APPEARS SOME WIREFORMS
ARE SLIGHTLY DIFFERENT TO THE MAJORITY OUT THERE. SOME ARE CURVED CLOSER TO THE TOP
AREA OF THE REEL, WHILE OTHERS ARE CURVED CLOSER TO THE RIGHT HAND SIDE OF THE REEL.
THE REEL ARM AND HANDLE CAN BOTH BE ADJUSTED 360 DEGREES.
TOOLS REQUIRED:
•
FLAT SLOTTED SCREWDRIVER
•
7MM/M4 SOCKET OR NUT DRIVER
PLEASE READ THROUGH THIS SECTION ENTIRELY BEFORE ADJUSTING THE REEL, TO AVOID
CAUSING DAMAGE TO THE REEL.
ENSURE YOUR HANDS ARE FRESHLY WASHED AND CLEAN PRIOR TO HANDLING THE REEL
EXCESSIVELY, THERE IS A THIN CLEAR COAT APPLIED BUT OVER HANDLING COULD CAUSE THE
NATURAL ACIDS ON YOUR HANDS TO POTENTIALLY DAMAGE THE PAINT APPLICATIONS.
QUINT'S REEL ADJUSTMENT
1.
THE HANDLE IS A FRICTION FITTED DESIGN
,
THIS IS TO ALLOW ADJUSTMENT WHILE
HOLDING ITSELF IN POSITION DURING
GAMEPLAY.
2.
THE HANDLE CAN BE ADJUSTED BY
HOLDING EITHER SIDE OF THE UPPER ARM
GREEN
ARROWS
AND TURNING THE
YELLOW HANDLE INTO THE DESIRED
POSITION.
3.
TURNING IT SLOWLY BUT FIRMLY WILL
ALLOW YOU TO MAKE MINOR
ADJUSTMENTS TO ITS POSITION.
4.
YOU CAN ALSO HOLD THE VERTICAL
COLUMN OF THE ARM LOCATED UNDER
THE YELLOW HANDLE.
5.
FOR FURTHER ADJUSTMENT, YOU CAN ROTATE THE REEL ARM USING A FLAT SLOTTED
SCREWDRIVER TO TURN THE ARM SCREW
YELLOW ARROW.
6.
IF THE ARM DOES NOT MOVE WITH MODERATE
FORCE TO THE FLAT SLOTTED SCREW, YOU WILL
NEED TO LOOSEN THE NYLON LOCKING NUT
RED ARROW
LOCATED UNDER THE REEL BASE
USING AN M4/7MM SOCKET OR NUT DRIVER.
7.
LOOSEN ONE SIDE IN HALF TURN INCREMENTS,
JUST ENOUGH SO YOU CAN MOVE THE ARM VIA
THE TOP SLOTTED SCREW.
8.
YOU
DO NOT
WANT THE ARM LOOSE TO THE
POINT IT MOVES FREELY.
9.
ONCE YOU HAVE ADJUSTED THE ARM AS
REQUIRED, TIGHTEN UP THE LOCKING NUT AND
FLAT SLOTTED SCREW AGAINST ONE ANOTHER.
10.
BEFORE YOU TIGHTEN THEM UP FIRMLY, PLACE
THE REEL TOPPER ON THE SPINNER AND TEST YOUR ADJUSTMENTS, IF THE
REEL IS NOW FREE OF
THE PREVIOUS CONTACT WITH THE WIREFORM, TIGHTEN UP THE LOCKING NUT AND SLOTTED
SCREW FIRMLY, SO THERE IS NO PLAY IN THE ARM.
ORCA BOAT WHEEL
- INSTALLATION INSTRUCTIONS
INSTALL GUIDE
•
INSTALL VIDEO (CLICK HERE) COMING SOON
TOOLS REQUIRED:
•
1/8” ALLEN KEY
•
5/64” OR 2” ALLEN KEY
•
FLAT SLOTTED SCREWDRIVER
•
7MM/M4 SOCKET OR NUT DRIVER
PLEASE READ THROUGH THE ENTIRE DOCUMENT FIRST BEFORE STARTING, TO ENSURE YOU
UNDERSTAND THE FULL SCOPE OF THE INSTALLATION.
IMPORTANT NOTES:
PLEASE WORK CAREFULLY AND TAKE YOUR TIME, I CAN TAKE NO RESPONSIBILITY FOR DAMAGE
CAUSED TO YOUR GAME DUE TO INCORRECT INSTALLATION OR WORK PRACTICES.
ORCA WHEEL INSTALL
1.
WITH THE PRECISION PINBALL
DISC UPGRADE INSTALLED,
REMOVE THE SECURING
SCREW FROM THE CENTRE OF
THE PRECISION PINBALL
SPINNING DISC USING A 1/8”
ALLEN KEY.
RED ARROW.
2.
IF YOU HAVE INSTALLED THE
BLACK STERN FACTORY
SCREWS
YELLOW ARROWS,
WHILE WAITING FOR YOUR
SPINNER TOPPERS TO ARRIVE,
THESE WILL NOW NEED TO BE
REMOVED.
3.
THIS IS DONE MUCH THE SAME AS THE REEL, REMOVE THE DISC FROM THE GAME AND REMOVE
BOTH SCREWS, THESE ONCE AGAIN WILL NOT BE NEEDED SO STORE THEM SAFELY IN YOUR COIN
BOX WITH THE TWO FACTORY SCREWS FROM YOUR MAIN PLAYFIELD “REEL” SPINNER.
4.
ONCE THE TOPSDE OF THE DISC IS CLEAR OF HARDWARE, PLACE THE ORCA BOAT WHEEL TOPPER
BASE ONTO THE PRECISION PINBALL DISC.
5.
UNLIKE THE REEL TOPPER/DISC THERE IS NO SPECIFIC ALIGNMENT REQUIRED.
6.
BEFORE PLACING THE ORCA WHEEL INTO THE WHEEL BASE, PLACE THE FIBRE WASHER INTO THE
SHAFT OF THE BASE, FOLLOWED BY THE ORCA WHEEL AND PRESS IT DOWN GENTLY INTO PLACE.
7.
NEXT TAKE THE 1” SECURING SCREW, SUPPLIED
WITH YOUR
WHEEL
TOPPER
AND LIKE YOU DID
WITH THE REEL TOPPER AND DISC, PINCH THEM TOGETHER TO HOLD THEM IN PLACE.
8.
NOW USING A 1/8” ALLEN KEY TIGHTEN THE SECURING SCREW THROUGH THE WHEEL AND
WHEEL BASE SECURING BOTH TO THE PRECISION PINBALL DISC.
9.
JUST LIKE WITH THE REEL, ENSURE THE CENTRE HEX SCREW IS TIGHTENED FIRMLY, UNTIL THE
WHEEL TOPPER IS SECURED TO THE DISC.
10.
IF FOR ANY REASON THE HEX SECURING SCREW IS NOT THREADING ALL THE WAY IN, REMOVE
THE SCREW AND USE THE SECOND FIBRE WASHER AND REPEAT FROM STEP #8.
THE INSTALLATION OF THE ORCA BOAT WHEEL SPINNER TOPPER IS NOW COMPLETE!
THANK YOU FOR YOUR PURCHASE OF QUINT’S REEL & ORCA BOAT WHEEL SPINNER TOPPERS.
YOUR SUPPORT IS GREATLY APPRECIATED.
PLEASE FOLLOW US ON:
GET IN TOUCH - WE WOULD LOVE TO HEAR FROM YOU!
YouTube
Facebook
Instagram
WEBSITE:
HotModsPinball.com
EMAIL ME:
hotmodspinball@gmail.com
PM ME ON PINSIDE:
J85M
